6 Considerations For Making The Exposed Aggregate Concrete 

Concrete is an essential constructional material when it comes to building anything walkable or foundational in Australia ranging from buildings, pavements, roads, aisles, pathways, to name a few. There are different ways of using the concrete as per its condition and types, each varies with the usage and preference of the builder or contractor. For instance, exposed aggregate concrete is considered ideal on the pathways or at the patio of your house. You can also use it for various improvisations in a home as it is highly durable and has a very user-friendly texture. But not everyone can handle the viscosity of the material as it requires professional handling to pull off the project with finesse and quality, therefore, you need to find a professional supplier and builder, respectively in order to complete the job at hand. Even if you intend to go all DIY on it, you would need to ensure the quality of concrete is impeccable or at par with your expectations before start working with it as received. Therefore, it is always recommended to take aboard an expert or a professional to guide you throughout the process of concrete application.

There are many contractors and suppliers of concrete in Australia but finding the one who is credible and deals in quality material is a difficult task, requiring you to go through a minute research before striking the final deal. The Brudetts in Australia has been lucky enough in this regard as their service over the span of 40 years has earned them a good name across the country, not only in providing top quality exposed aggregate concrete but also in delivering it at the sites of operation in time.

However, once you have got the quality concrete material, then the next consideration is: it is imperative to be very cautious when it would come to the use of the material for turning it into the exposed aggregate concrete; hence, below are given a few tips for applying exposed aggregate concrete at the site, such as:

Define The Aggregate

The first step in making the exposed aggregate concrete Melbourne is to first define the size and color of the aggregate that you want to project in the finished project or item. For instance, if you are working on the driveway of a parking lot then you would be needing an expert on board to consult you over the right size of the aggregate as the smaller the size the more weight it could support or carry. Rule of thumb is if you are even in the slightest doubt, seek insights from the material supplier.

Prepare The Base

The second step in preparing aggregate concrete Australia is to prepare the subgrade base underneath it. For this purpose, you will need to remove all the organic residuals from the site of the project then fill it with stones or sand; if required, you can grade and compact it. Bear in mind that the subgrade base must be 3.5’’ below the top finished surface in order to keep from any discrepancies. Also, one must ensure that rainwater does not seep through the surfaces, for that you can make slopes of 1’’ across the baseline after every 1 foot.

Work On The Form

Next comes the shape of the project at hand, you will have to use stakes according to the required size to form a layout or a board to define the overall shape of the project. Make sure that the corners are at 90 degrees otherwise adjust or amend the shape by using the stake. For instance, if you are using stakes of size 2×4 then it will leave have the capacity of up to 3.5’’ tall to pour the concrete in it. If you want to have a denser or thicker concrete layer then increase the size of the stakes as per desire.

Pour Concrete

Once the shape is defined then to execute the exposed aggregate concrete Melbourne, you now require to pour the concrete in the form by using a board of the same size of the stakes. Once you have poured the concrete then put the plank upon it and sway it back and forth until the final surface turns smooth.

Surface Retarder

Spray surface retarder on the blocks or the form In order to slow down the curing process. It should be cure enough to hold the desired weight, ambients temperature and the director of retarder application defines the timing in this regard. Bear in mind that, the concrete must not dislodge once cured appropriately as per the project. Also, if you would wait for too long, the more difficult the next task would become; hence, find the balance.

Expose The Surface

Lastly expose the surface by scrubbing and rubbing it off with a hose or a scrubber; however, ensure that you scrub off only ⅓ part of it in order to not challenge the durability of it.

It is not easier to deal with the exposed aggregate concrete in Australia, you need to have a concrete expert by your side to derive the beauty, safety, and strength out of the material by following the right process of aggregating and exposing it else risk would be a lot higher.


No responses yet

Leave a Reply